Experimental evaluation of the luminescence performance of fired clay brick coated with SrAl2O4:Eu/Dy phosphor

This study evaluates the luminescence performance of fired clay bricks coated with SrAl₂O₄:Eu/Dy phosphor. To do so, SrAl₂O₄:Eu/Dy phosphor was first produced using the traditional solid-state reaction synthesis technique. The prepared phosphor was then used for coating fired clay bricks to analyze the luminescence performance via spectral analysis, decay characteristics, and microstructure of the bricks. The results reveal that excitation and emission spectra of the phosphor coated bricks range from 200 to 480 nm and 455 to 650 nm, respectively, suggesting that the phosphor coated bricks have the capacity of absorbing light with a wide range of wavelengths. The peak wavelength projected at 511 nm in the emission spectrum is achieved, which indicates 4f⁶5 d¹-4f⁷ transition of Europium (Eu²⁺). The repeated excitation and deexcitation of Eu²⁺ by using hole traps and trap levels offered by Dysprosium (Dy³⁺), exist between the ground and the excited state of Eu²⁺ leads to luminescent phenomenon. Moreover, the decay characteristics has revealed that phosphor coated bricks can emit light for a considerable amount of time (>8.5 min) upon the removal of the excitation source. The results reveal that phosphor coated bricks has the potential of increasing energy efficiency of residential and commercial buildings.     

Hydrogen production performance of a photovoltaic thermal system coupled with a proton exchange membrane electrolysis cell

As one of the cleanest energies, hydrogen has attracted much attention over the past decade. Hydrogen can be produced using water electrolysis in a Proton Exchange Membrane Electrolysis Cell (PEMEC). In the present study, the performance of the PEMEC, powered by the Photovoltaic-Thermal (PVT) system, is scrutinized. It is considered that the PVT system provides the required electrical power of the PEMEC and preheats the feedwater. A comprehensive numerical model of the coupled PVT-PEMEC system is developed. The model is used to investigate the effect of various operating parameters, including solar radiation intensity, inlet feedwater temperature, and feedwater mass flow rate, on the hydrogen production and operating voltage of the PEMEC at various Exchange Current Densities (ECDs). Furthermore, the effect of integration of Phase Change Material (PCM) and Thermoelectric Generator (TEG) on the hydrogen production of the system is evaluated. According to the obtained results, the PVT-TEG-PEMEC system outperforms other systems in hydrogen production. However, integration of the PVT-PEMEC system with PCM has a negligible effect on its hydrogen production.     

A survey on tracking control of unmanned underwater vehicles: Experiments-based approach

This paper aims to provide a review of the conceptual design and theoretical framework of the main control schemes proposed in the literature for unmanned underwater vehicles (UUVs). Additionally, the objective of the paper is not only to present an overview of the recent control architectures validated on UUVs but also to give detailed experimental-based comparative studies of the proposed control schemes. To this end, the main control schemes, including proportional–integral–derivative (PID) based, sliding mode control (SMC) based, adaptive based, observation-based, model predictive control (MPC) based, combined control techniques, are revisited in order to consolidate the principal efforts made in the last two decades by the automatic control community in the field. Besides implementing some key tracking control schemes from the classification mentioned above on Leonard UUV, several real-time experimental scenarios are tested, under different operating conditions, to evaluate and compare the efficiency of the selected tracking control schemes. Furthermore, we point out potential investigation gaps and future research trends at the end of this survey.     

Simulation of interaction between high-temperature process and heat emission from electricity system in summer

During the hot summer season, using electricity systems increases the local anthropogenic heat emission, further increasing the temperature. Regarding anthropogenic heat sources, electric energy consumption, heat generation, indoor and outdoor heat transfer, and exchange in buildings play a critical role in the change in the urban thermal environment. Therefore, the Weather Research and Forecasting (WRF) Model was applied in this study to investigate the heat generation from an indoor electricity system and its influence on the outdoor thermal environment. Through the building effect parameterization (BEP) of a multistorey urban canopy scheme, a building energy model (BEM) to increase the influence of indoor air conditioning on the electricity consumption system was proposed. In other words, the BEP+BEM urban canopy parameterization scheme was set. High temperatures and a summer heat wave were simulated as the background weather. The results show that using the BEP+BEM parameterization scheme of indoor and outdoor energy exchange in the WRF model can better simulate the air temperature near the surface layer on a sunny summer. During the day, the turning on the air conditioning and other electrical systems have no obvious effect on the air temperature near the surface layer in the city, whereas at night, the air temperature generally increases by 0.6 ℃, especially in densely populated areas, with a maximum temperature rise of approximately 1.2 ℃ from 22:00 to 23:00. When the indoor air conditioning target temperature is adjusted to 25–27 ℃, the total energy release of the air conditioning system is reduced by 12.66%, and the temperature drops the most from 13:00 to 16:00, with an average of approximately 1 ℃. Further, the denser the building is, the greater the temperature drop.     

Powder sintering and gel casting methods in making glass foam using waste glass: A review on parameters,performance, and challenges

The application of insulation materials in buildings and energy storage facilities is gaining global attention to reduce energy consumption, heat loss, and CO₂ emissions. Given the high insulation performance, glass foam is gaining popularity replacing combustible, high energy-consuming, and costly conventional insulation materials. The industrial process of glass foam manufacturing is an energy-consuming and non-ecofriendly process which requires the annealing of glass around its melting temperature. Therefore, researchers have developed powder sintering and gel casting methods to sinter glass foam mix at a temperature slightly above its glass transition point. However, research findings on these two methods are scattered because of the different parameters being used by researchers. The properties and performances of glass foam depend on the processing parameters, especially on the materials design and sintering conditions. Therefore, this study aimed to provide a comprehensive review on the key parameters for material selection and sintering of glass foams and provide necessary guidelines for the best practice and a direction for future research. Moreover, this review covers the current strategies and challenges associated with the powder sintering and gel casting methods including their sustainability and environmental performance.     

Effects of alkali metal ion on imprinting GRIN microstructure in GeS2-Ga2S3-MCl (M=Na,K, Cs) glasses for visible to mid-infrared microgratings

Gradient refractive index (GRIN) micro-optics present unique opportunities for control of the chromatic properties, new degrees of freedom for optical design as well as the potential for use in new optical system applications. GRIN microgratings were imprinted in GeS₂-Ga₂S₃-MCl (M = Na, K, Cs) chalcohalide glasses by microthermal poling, and the effects of the type and concentration of alkali cations on their performance were investigated. Two effective imprinting formation regions of the GRIN microstructure based on the poling saturation voltage (U_s) and glass composition are observed at fixed poling time and temperature. The U_s increases from 140 to 750 and 2600 V in accordance with the activation energy (E_a) of alkali ions (Na⁺ to K⁺ and Cs⁺) increasing from 45.15 to 58.62 and 92.58 kJ/mol for studied samples. The saturated numbers of diffraction order (N_s) of the gratings in these samples are 7, 9 and 6, respectively, the highest number being provided by the K⁺-containing sample. This is in accordance with imprinting-induced phase differences (0.14λ, 0.19λ and 0.09λ) measured in the fabricated samples containing Na⁺, K⁺ and Cs⁺ ions. Furthermore, the U_s of samples decreases from 1500 to 300 V with four concentrations of K⁺ from 10 to 30%, associated with their E_a of K⁺ decreasing from 69.62 to 53.46 kJ/mol, while N_s increases from 8 to 14, which is attributed to the increase of the phase difference in the GRIN structures. The controllable GRIN microstructures are realized by adjusting the type and concentration of alkali cations in chalcohalide glasses, which is expected to drive the design of broadband GRIN microgratings.     

Spark plasma sintering of UO2 nanopowders: Pressure,heating rate and current effects

We analysed with different methods the densification of UO₂ nanopowders in SPS under constant heating rate (CHR) and isothermal sintering conditions. The apparent activation energy of densification in SPS (75 kJ/mol with CHR method) is significantly smaller than in conventional sintering. It is shown that this is likely not an effect of the applied current. We also observed a threshold stress at 64 MPa for the transition from pressure-insensitive sintering (stress exponent n≈0) to pressure-assisted sintering, suggesting that the contribution of the capillary stresses in such nanopowders is comparable with the typical stress applied in SPS.     

Molecular design for thermally stable SiZrBOC structure from single source precursor with high ceramic yield

A new type of high-temperature-resistant SiZrBOC ceramics was prepared by sol-gel method using polymethyl-hydro siloxane (PMHS), boric acid (B(OH)₃), and n-propyl zirconate (Zr(OPr)₄) as raw materials. After high-temperature pyrolysis, the SiZrBOC precursor was transformed into a crystalline ceramic material with a yield of 89.5 wt%. Fourier infrared spectroscopy (FT-IR) and thermogravimetric analysis (TGA) were applied to characterize the polymer-ceramic conversion process and thermal behavior of ceramic precursors. According to the results, the addition of boron elements led to the formation of Si-O-B links in the system. X-ray diffraction (XRD) and transmission electron microscopy (TEM) were used to study the phase composition and microstructure of SiZrBOC ceramics. Finally, the oxidation test at 1200 °C revealed that SiZrBOC ceramics with a boron/zirconium molar ratio of 2.5:1 exhibited the best oxidation resistance at a weight gain of 0.4 wt% only.     

Kinetic Monte Carlo simulation of hydrogen production from photocatalytic water splitting in the presence of methanol by 1 wt% Au/TiO2

In this research, using the kinetic Monte Carlo simulation (KMC), the hydrogen production from a water-methanol mixture using Au/TiO₂ photocatalyst is investigated. A mechanism is proposed, and the rate constants of the reaction steps are specified. The reaction rate constants of different steps and the concentration of the active sites on the photocatalyst surface were determined. An excellent match between simulated and experimental data confirms the results. The electron-hole pair production, methanol adsorption on the photocatalyst surface, and electron-hole recombination steps are considered the most critical steps. To study the effects of independent variables (initial concentration of methanol, photocatalyst dosage, pH, and time of reaction) on the produced hydrogen, a combination of KMC simulation and design of experiment was employed. The concentration of photocatalysis has the highest and pH has the lowest effect on the hydrogen production. The optimal conditions for photocatalytic hydrogen production are presented.